Home WINDOWS HOW-TO Fix Cloned SSD Won’t Boot Windows 10 or Windows 11

Fix Cloned SSD Won’t Boot Windows 10 or Windows 11

0
Fix Cloned SSD Won’t Boot Windows 10 or Windows 11

[ad_1]

To eliminate the need to reinstall Windows 11 or Windows 10 on a new drive, most PC users prefer to directly clone the hard drive and then transfer the installation to the SSD, but in some cases, after transferring the Windows installation to the SSD, the drive may not fully boot or an error code appears on startup. 0xc000000f. This post identifies potential causes and also suggests the most appropriate solutions to solve the problem.

Below are some of the possible reasons why you might encounter this problem:

  • The original disk that you cloned contains bad sectors.
  • You connect the SSD to your computer via USB.
  • Lack of specific drivers for loading SSD.
  • Unexpected errors occur during the cloning process.
  • Style conflict for GPT / MBR partitions.
  • You have installed the wrong boot disk.
  • The “System Reserved” partition is missing when cloning.
  • System partition is not set as active partition

Cloned SSD won’t boot Windows 10 or Windows 11

If your cloned SSD won’t load the Windows 11/10 operating system on your computer, you can try our recommended solutions below in no particular order and see if it helps fix the problem.

  1. Disable other external boot devices
  2. Make sure the SSD is properly connected to the computer.
  3. Set the correct boot mode (from UEFI or Legacy)
  4. Change boot order to boot from cloned SSD
  5. Recover MBR for SSD
  6. Set system partition as active partition
  7. Repeat the cloning process
  8. Clean install Windows to SSD

Let’s take a look at a description of the process associated with each of the listed solutions.

1]Disable other external boot devices.

When troubleshooting for the first time, you can try to fix Cloned SSD won’t boot Windows 11/10 on your PC – disable other external boot devices – because in some cases, if there are other external boot devices connected, such as a bootable USB stick or bootable CD / DVD drive, these devices may interfere with the boot of your cloned SSD.

If this scenario does not work for you, continue to the next solution.

2]Make sure the SSD is properly connected to the computer.

Your next step is to make sure the cloned SSD is properly connected to your computer. You need to check if the SSD is properly connected to your computer – otherwise the cloned SSD won’t boot. If this happens, disconnect the drive and then carefully reconnect it to the computer. Also, use a SATA cable instead of USB to connect your SSD to your computer.

3]Set the correct boot mode (from UEFI or Legacy)

V MBR works with Legacy launch mode and GPT works with UEFI. If the partition style is incompatible with the boot mode, you will face this problem. Cloned SSD won’t boot with wrong boot mode – MBR or GPT. In this case, in order to solve the problem you have encountered, you need to change the boot mode according to your preset partition style.

To change the boot mode on Windows 11/10 PC, do the following:

  • Boot into BIOS.
  • Use the arrow key to select Boot
  • Use the arrow key to select UEFI / BIOS Boot Mode
  • Press Enter.
  • Now select Heritage or UEFI according to your preset section style.
  • Click on F10 to save the settings.
  • Reboot your computer.

Make sure the issue is resolved, otherwise try the next solution.

4]Change the boot order to boot from the cloned SSD.

This solution requires you to reverse the boot order to boot from the cloned SSD.

5]Recover MBR for SSD

If the MBR (Master Boot Record) on the cloned SSD is damaged, the system cannot be booted. In that case, you can repair the MBR and see if that helps.

6]Set system partition as active partition

Typically, the active partition should be the primary partition. The boot files for the Windows 11/10 operating system are located in the main partition. Thus, if the system partition is not set as active, Windows will not boot after cloning to the SSD. In this case, in order to fix the problem, you need to change the active partition by following the instructions in the fix guide The drive where Windows is installed is locked – for this, since the cloned SSD won’t boot, you will have to boot from the old hard drive, then insert the SSD into the hard drive enclosure and connect the enclosure to the PC.

7]Repeat the cloning process

Most likely, some errors might have occurred during the cloning process, but you don’t know. To rule out this possibility, you can try to fix your problem by repeating the cloning process, but be sure to use professional and reliable cloning tools so that the cloned SSD can work as expected. You can also install, reinstall, clone Windows without DVD / USB using WinToHDD on your computer.

8]Clean install Windows to SSD

As a last resort, if all else fails, you can back up your files and then do a clean install of Windows 11/10 to the SSD.

Hope this helps!

How do I make my SSD bootable after cloning?

To make your SSD bootable after cloning or to boot from a cloned SSD, do the following:

  • Restart your computer, press F2 / F8 / F11 or Del to enter the BIOS environment.
  • Go to the boot section.
  • Set the cloned SSD as a boot drive in BIOS.
  • Save changes and restart your computer.

You can now successfully boot your computer from the SSD.

How to fix the cloned SSD won’t boot?

Among other known solutions to fix cloned SSD not booting, you can try the following suggestions: Use a SATA cable instead of a USB patch cable. Correctly install the solid state drive to the computer using the SATA cable.

[ad_2]

Source link

windows789.com

LEAVE A REPLY

Please enter your comment!
Please enter your name here